Outils

The Charger 2 wrench is designed for use on the lower seal head of Charger 2 and Charger LT dampers. This series of wrenches comes as a result of our collaboration with RockShox to develop a series of tools specifically for their suspension components. Built to hold the thin aluminum parts of the dampers to avoid damage. These wrenches are built with the same tool grade aluminum to tight tolerances to give you years of trouble free use. They will not damage or mar the sensitive parts inside your suspension fork when used with care, keeping you and your customers happy. They also feature a 3/8" square drive in the middle to use with your favorite torque wrench during reassembly.

The Reverb is an advanced and complicated component and service becomes a breeze with this speciality wrench. Designed for use on the inner seal head and upper collet of both 30.9 and 31.6 millimeter version of the Reverb dropper post. This series of wrenches comes as a result of our collaboration with RockShox to develop a series of tools specifically for their suspension components. Built to hold the thin aluminum parts of the dampers to avoid damage. These wrenches are built with the same tool grade aluminum to tight tolerances to give you years of trouble free use. They will not damage or mar the sensitive parts inside your seastpost when used with care, keeping you and your customers happy. They also feature a 3/8" square drive in the middle to use with your favorite torque wrench during reassembly.

Many athletes are fortunate enough to be able to ride nearly anything. For those that are sensitive to bike fit though, replicating fit to a new bike or confirming fit after travel can be a challenge involving lots of trial and error. This set of tools allows accurate and repeatable measurements for saddle height, angle and setback. The accuracy and repeatable measurements also serve as a base to make adjustments to fit. -The magnetic saddle height bullets ensure you get an accurate center at the BB by locating in the crank arm fixing bolt or the crank arm preload cap of Shimano caps. This allows you to focus on the smart end of the tape measure at the saddle plate. -Two reference marks on the saddle plate means you can pull a measurement to the exact same spot relative to the nose of the saddle every time. This gives you accuracy down to a single millimeter. -The front of the saddle plate is engraved with a ruler, to allow you to calculate saddle setback at the saddle. This allows you to drop the plumb bob off the side of the bike and clear all of the bottle cages. -The wide plate has ample room to mount a level, protractor or smart phone for adjusting the angle of the saddle. This is particularly helpful for non traditional saddles like SMP and Adamo.

- The Pro bearing punch tool-kit allows fast removal of bearings in suspension linkages and hubsets. - The steel punches locate on the inside diameter of a bearing in order to drive the bearing out of the bore. - The bearing punch kit includes 8, 10, 12, 15, 17, 18 and 20mm sizes and include a tool roll for organized shop use and travel.

- Removes bearings from hubs and various other items - Works on bearings with an internal diameter of 8-32mm

- Tool for pulling and pressing bottom bracket bearings. - For all BB30 frames and bearings - Allows the bearing to be pulled without damage for cleaning and re-greasing - Also safely presses bearings back into cups - Instructions included

- Hub bearing press set with 10 guides - For ID 8-20mm

- Clamp height adjusts from 41.75"- 56.75" (106 to 144 cm) to allow you to work at a comfortable level - Clamp head rotates 360° - The articulating jaw on the clamp provides a large clamp opening, allowing the bike to be easily inserted and removed by flipping the cam lever. - Clamp head is micro-adjustable to accommodate various tube sizes. - No tools required for quick setup and storage - Lightweight aluminum construction - Product Weight: 13.6 lbs (6.18 kg) - Max load capacity: 77 lbs (35 kg)

Being a "shade tree mechanic" doesn't mean you should lean your bike against a tree. You paid hard-earned money for your family's bike collection and we've got a budget-conscious, yet feature-loaded bike repair stand that's perfect for the home bike mechanic. The price-point leading 360-degree rotating clamp can position your bike optimally for any work you're planning. Plus, the Recreational Stand leverages a 52-inch (132cm) wide base with rubber-coated end caps for fantastic stability on any surface. And when the service day is done, it folds into a space-saving unit for storage. Add a Tool Tray, Bottle Opener, and a Pro Truing Stand for the complete at-home bike shop. - Seatpost clamp features Spinner Knob for quick closure and precision clamping pressure - 360-degree rotating clamp design provides easy access to any part of your bicycle - Fixed clamp height at 55-inch (139cm) - Rubber-coated clamp secures and protects expensive components and beautifully painted frames - Clamp opening up to 1.9-inch (4.8cm) accommodates even the largest diameter frame tubes - Powder-coated steel construction is corrosion-resistant and incredibly durable - Stiff 52-inch (132cm) base and rubber-coated end caps create ultimate stability even on uneven surfaces - Total load capacity of 60lbs (27.2kg) accommodates service on most road, mountain bikes, fitness bikes, and electric bikes - Portable and compact construction creates a remarkably small folded footprint of 10 x 4 x 55-inches (25.4 x 10.2 x 139.7cm) - Optional Travel Bag available - At 13.8lbs (6.3kg), moving in and out of storage is no problem - No assembly required - 3-year Warranty

- The world's fastest race lube… period - Ultra-low coefficient of friction - Class-leading low wear on chain components - Provides the ultimate performance in both wet and damp or dry and dusty conditions - Continues to improve with chain run-in due to continued surface improvement at a molecular level - Non-wax based lubricant - Outperforms competitor chain lubes and waxes - Biodegradable and sustainable - Proprietary additives for self-lubricating capabilities - Synthetic polymers for long-distance performance - Works in temperatures down to -20°C - Low noise formulation - Pipette system for easy application

- Water based liquid with advanced surfactants resulting in excellent degreasing - Anti-corrosion agent added to solution to protect steel parts - Due to natural evaporation and splashes, expect to lose 8-10L per month from tank

Bundle includes qty 1 of the following: - Pressure Washer with all lances - Storage bag - Snow Foam Lance - Nano-Tech Bike Cleaner, 1L (900933-02) - Nano-Tech Cleaner Concentrate, 1L (901007-02) - Bike Protect, 500ml (901684-01) - Drivetrain Cleaner, 500ml (901101-01) - C3 Dry Lube, 120ml (900965-02) - Qty 2 Premium Microfiber Polishing Cloth (901555-01)

A daily-use, shop version of Park Tool's world-famous CM-5.2 Chain Scrubber. The CM-25 features a super-tough die-cast aluminum case and handle, plus a unique brush/sponge replacement cartridge that makes it easy to keep it running smoothly and working properly. Park Tool's proven four-sided scrubbing action makes thoroughly cleaning chains quick and easy. A shop quality cleaner built to give years of constant use. - Proven chain scrubbing technology leaves chains sparkling clean - Durable A380 aluminum die cast case and removable handle - Dual-sided sponges and wicking pads to help reduce drips - Rotating brushes clean on all four sides of every link - Brush and sponge cartridge quickly and easily clicks in and out (RBS-25) - Locking cover with stainless steel hinge pins - Choose drip or immersion fluid application methods - 100% serviceable

Includes a new tray/motor shroud, USB ports and oversized buttons to upgrade a Park Tool PRS-33 or PRS-33 AOK into the PRS-33.2 version controls and electronics.

With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The TW-6.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). Designed for higher torque settings for repairs and installation in the bottom bracket, cassette lockring and other areas that use a higher torque settings. For lower torque setting, see the TW-5. Comes with its own protective case. - 10–60 Newton meter range (88–530 Inch Pounds) - Adjustable in 0.25 Nm increments - Ratcheting 3/8" drive - Reads and registers for both left hand and right hand threading - Dial-adjust system allows desired torque setting to be preset - Calibrated to be accurate to +/- 4% - Length: 36.2cm (14.25")

The BKD-1.2 Hydraulic Brake Bleed Kit will bleed most models of DOT fluid-based hydraulic disc brakes, including models made by SRAM®, Formula®, Hayes®, and Hope®. Bleeding of hydraulic brakes removes air bubbles and contaminants from the braking system, for long-lasting components and peak performance. The BKD-1.2 is built for the rigors of daily commercial use and includes two syringes, hoses with shutoff clips, multi-size bleed blocks, and a set of our unique mountable syringe holders, as well as multiple hose fittings to fit the multiple standards found on hydraulic bicycle brake systems. Every part is replaceable and available from Park Tool. Housed in a rugged storage case. Includes: - Two 20 mL syringes Two hose assemblies with shutoff clips - Two 10 mm/12 mm universal bleed blocks - Two 11 mm bleed blocks for Hayes® systems -  Two adjustable syringe holders -  M5 x 0.8 adapters— SRAM® (x2) -  M6 x 1.0 adapter— universal (x2) - Bleeding Edge-specific fitting — SRAM® -  Hose compression sleeve — universal -  Set of spare O-rings and hose -  Replacement parts available -  Brake fluid not included NOTE: The BKD-1.2 is for DOT fluid-based hydraulic bicycle brake systems only. DOT fluid and mineral oil should never be mixed in the brake system or in their respective service tools. Cross-contamination of brake fluid may cause seal failure which may result in brake failure. For mineral oil brake systems use the Park Tool BKM-1.2 Hydraulic Brake Bleed Kit — Mineral Oil.

An alignment gauge is essential for diagnosing and repairing bent or misaligned derailleur hangers, often the source of shifting problems. The DAG-3 features an all-new design, engineered and built to be light, accurate, and versatile. The sliding indicator can measure derailleur hanger alignment against bicycle rims of any size and rotates out of the way to clear seat stays, racks, and other obstacles, allowing 360-degree measurement. The long, precision-extruded aluminum body is built to exacting tolerances and provides ample leverage for making adjustments. - Compatible with 16" to 29"+ wheels (ISO/ETRTO rim sizes from 317 to 630+) - Replaceable M10 threaded tip - Low-profile head fits low clearance thru-axle derailleur hangers and Shimano Direct Mount hangers - Length: 16.5" (420mm) - Weight: 22.75 oz. (645g)

A complete tool set to work on both Campagnolo and Fulcrum Ultra-Torque and Power Torque crank and bottom bracket systems (each sold separately). The CBP-8 includes a beefed-up bearing and crank puller and all the fittings necessary to remove and install both systems. - Bearing Puller That Fits Both Power Torque And Ultra-Torque - Crank Puller For Power Torque - Bearing Setter For Both Power Torque And Ultra-Torque - Removal Adaptor For Power Torque Crank Bearings - Removal Protection Pads For Use With Carbon Cranks - Removal Protection Adaptor For Use With Aluminum Crank Arms - Crank Removal Extension Plug For Power Torque

The CRS-15.2 uses two different insert rings to install bearing races on the 1.5-inch and 1-1/4-inch forks. The bearing surface is spared a direct hit by using aluminum inserts. Using a hammer, tap firmly on the end cap of the tube and seat the race into its proper place safely and accurately. Included extension allows work on fork steering tubes up to 425mm. - SHIS terminology: The CRS-15 services crown races in SHIS 33 and 40.

No more need to hold wheels between your knees, balance on a bench top or ask for help. The WH-1 Wheel Holder firmly holds thru axle and quick release wheels at three convenient positions. It’s like having a strong helper to hold wheels during cleaning, tire and tube work, hub work, cassette work, and tubeless installation. The WH-1 can be bolted or clamped directly to a bench or installed in a bench vise. Uses and Features: - Quick and easy access to hold virtually any wheel to perfectly position your work for a variety of tasks including but not limited to: - Wheel building -Cassette removal and installation - Tire and tube removal and installation - Tubeless tire work - General cleaning - Hub work - Holds wheel at vertical, 35 degrees from vertical, and horizontal positions - Accepts 12, 15, and 20mm thru axles and 5mm skewers - E-Nickel finish for durability

Designed and built specifically for a wide variety of bicycle Torx compatible work, the THT-1 is a set of eight common sizes of professional quality T-Handle star-shaped wrenches built for speed, efficiency, leverage and a perfect fit. Soon to become your favorite Torx compatible set, the THT-1 includes a handy tool holder that mounts to any vertical surface, including pegboard and solid surfaces (fasteners not included). - Carefully selected combination of Chrome Vanadium and S-2 tool steels - T6, T8, T10, T15, T20, T25, T30 and T40 Torx compatible wrenches included - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Sliding T-handle creates increased leverage and multiple access positions - Tool holder is included with the set and mounts to any wall, bench or tool box, perfectly positioning each wrench for easy access and storage

A versatile and convenient way to keep tools, supplies and technology at arms length on a PRS-33 Power Lift Repair Stand. The PRS-33TT solidly mounts directly to either side of the stand’s upright at any height. - 19 tool holding holes, slots and small trays in a variety of shapes and sizes - 14-inch (35cm) magnetic tool bar - Integrated mounting holes for PTH-1 Paper Towel Holder - Phone/tablet/clipboard holder - Pen and pencil holders - Adjustable utility hook to hang wheels, parts and scales - Height adjustable - Can be installed on a fully assembled stand

The BKM-1.2 Hydraulic Brake Bleed Kit will bleed most models of mineral oil-based hydraulic bicycle disc brakes, including models made by Shimano®, Magura®, TRP®, Tektro®, Trick Stuff®, SRAM® DB8, Campagnolo®, Promax®, and Clarks®. Bleeding of hydraulic brakes removes air bubbles and contaminants from the braking system, for long-lasting components and peak performance. The BKM-1.2 is built for the rigors of daily commercial use and includes two syringes, hoses with shutoff clips, multi-size bleed blocks, a bleed funnel, and a set of our unique mountable syringe holders, as well as multiple hose fittings to fit the multiple standards found on hydraulic bicycle brake systems. Every part is replaceable and available from Park Tool. Housed in a rugged storage case. Includes: -  Two 20 mL syringes -  Two hose assemblies with shutoff clips -  One hose assembly with integrated fitting for bleed nipples such as those found on Shimano® mineral oil brake systems -  One open-ended hose assembly -  Bleed funnel with stopper -  Two 10 mm/12 mm universal bleed blocks -  Two 11 mm bleed blocks -  Two adjustable syringe holders -  M4 x 0.7 adapters — SRAM® DB8, Trick Stuff®, Campagnolo® (x2) -  M5 x 0.8 adapter — Formula™ Cura™, Tektro®, Hayes® (x2) -  M6 x 0.75 adapter — Magura® -  M6 x 1.0 adapters — universal (x2) -  M6 x 1.0 adapter — Promax® -  M7 x 0.75 adapter — Shimano® -  Hose compression sleeve — universal -  Fluid disposal bag -  Set of spare O-rings and hose -  Replacement parts available -  Brake fluid not included NOTE: The BKM-1.2 is for mineral oil-based hydraulic bicycle brake systems only. DOT fluid and mineral oil should never be mixed in the brake system or in their respective service tools. Cross-contamination of brake fluid may cause seal failure which may result in brake failure. For brakes using DOT fluid use the Park Tool BKD-1.2 Hydraulic Brake Bleed Kit — DOT.

Designed and built specifically for a wide variety of bicycle hex work the THH-1 is a set of eight common sizes of professional quality T-Handle hex wrenches built for speed, efficiency, leverage and a perfect fit. Soon to become your favorite hex set, the THH-1 includes a handy tool holder that mounts to any vertical surface, including pegboard and solid surfaces (fasteners not included). - Carefully selected combination of Chrome Vanadium and S-2 tool steels - 2, 2.5, 3, 4, 5, 6, 8 and 10mm hex wrenches included - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Machined, chamfered tips allow easier insertion into hex fittings - Integrated “Strip-Gripper” twisted hex that makes removal of most bolts with stripped or over-sized hexes fast and easy - Sliding T-handle creates increased leverage and multiple access positions - Tool holder is included with the set and mounts to any wall, bench or tool box, perfectly positioning each wrench for easy access and storage

The 37-piece SBS-3 from Park Tool is a comprehensive, shop-quality set of sockets, hex bits, and Torx compatible drivers selected specifically to tackle a wide variety of common bike repair needs. The SBS-3 also includes flat-faced sockets in common sizes for work on suspension forks. Ideal for use with Park Tool torque wrenches, the 3/8" drive bits and sockets are forged from tough, chrome vanadium steel and nickel chrome plated for lasting durability.

World-famous Park Tool quality wrapped up in a great set of metric combination wrenches. The MWR-SET includes 6mm to 17mm wrenches with a 12-point two-way ratcheting box end. Forged from chrome vanadium steel, chrome-plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip. Strong, comfortable, and beautiful! - Includes 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, and 17mm wrenches

Park's Home Mechanic Wheel Truing Stand allows extremely accurate and reliable wheel truing and even building at an economical price. It's constructed from heavy-gauge steel and works with most wheel sizes and hub widths. It can be bolted to a bench for additional stability.

Improperly aligned frame or fork dropouts can cause bent axles and quick-release skewers, as well as tracking and shifting problems. The Frame and Fork End Alignment Gauge Set quickly determines whether the frame or fork dropouts are aligned and parallel. If an error is detected, long handles and comfortable molded grips afford plenty of leverage for straightening. These Park gauges adjust to compensate for various hub widths from 100mm to 160mm, too.

After years of research and testing, Park Tool's built what they consider the best shop clamp made. It’s smooth, versatile and built to stand up to everyday shop use. • #100-3D fits the following repair stands: PRS-2, PRS-2 OS, PRS-2 OS-1, PRS-2 OS-2, PRS-3, PRS-3 OS, PRS-3 OS-1, PRS-3 OS-2, PRS-3.2-1, PRS-3.2-2, PRS-4, PRS-4 OS, PRS-4 OS-1, PRS-4OS-2, PRS-4W and PRS-33 • #100-5D fits PCS-4, PRS-7, some models of PRS-5 (with composite top tubes), and PCS-1 models manufacturer post 2002. (Note: Inspect top tube below lever for an embossed "939") • #100-25D fits PRS-25, PCS-10, PCS-11, PCS-12 (and PRS-15 with 1951-15 Adaptor Stud) • Grips nearly any tube from 7/8” to 3” (23–76mm), including aero tubes • Micro-adjustability allows perfect clamping pressure every time and prevents damage to thin-walled tubes • Long travel cam handle allows quick entry, adjustment and exit • Versatile: It grips nearly any tube including aero shaped tubing and seat posts 7/8” to 3” (23mm-76mm). Its narrow clamping jaws (2.7”/7cm) are designed to clamp securely yet fit into tight areas or on short seat posts. • Durable, replaceable jaw covers • Soft Touch saddle cradle provides a perfect spot to temporarily rest a bike by its saddle • Built to last: Powder coated, precision machined, die-cast aluminum main body parts and high quality small parts • Fast operation: Cam-actuated adjustment system for quick entry, adjustment and exit, plus handy “spinner” handle helps speed large size range adjustments

The 2197 is an add-on accessory for the Park Tool DT-5 and DT-5.2 Disc Brake Mount Facing Set to enable easier and more efficient facing of disc brake mounts on carbon fiber frames. Features a brazed-on diamond grit surface that is over 100 times more durable and effective on carbon fiber than the cutter included with the DT-5.2. The 2197 sits between the cutter of the DT-5.2 and the brake mount, and smoothly and evenly grinds the mounting surface until it is flat and properly perpendicular to the rotor. NOTE: The 2197 is intended for facing carbon fiber only. Aluminum, steel, and titanium disc brake mounts should be faced using the #2171 facing cutter included with the DT-5.2. For carbon frames that feature aluminum inserts (with a carbon/aluminum hybrid mounting surface), use the #2197. When machining carbon fiber, regularly apply water (or a similar solution) to the cutting surface.